How to Check 2010 1.6 DOHC Hyundai Elantra

P0712 Transaxle Fluid Temperature Sensor Circuit Low Circuit

Study Guide Component Inspection Check "TRANSAXLE FLUID TEMPERATURE SENSOR" 1. Study Ignition "OFF" . 2. Study Disconnect the "TRANSAXLE FLUID TEMPERATURE SENSOR" connector 3. Study Measure the resistance between terminals "5" and "6" of the "TRANSAXLE FLUID TEMPERATURE SENSOR". A. Study the Specification : Refer to " Reference data" TEMP.(°C) RESISTANCE(kΩ) TEMP.(°C) RESISTANCE(kΩ) -40(-40°F) 139.5 80(176°F) 1.08 -20(-4°F) 47.7 100(212°F) 0.63 0(32°F) 18.6 120(248°F) 0.38 20(68°F) 8.1 140(284°F) 0.25 40(104°F) 3.8 160(320°F) 0.16 60(140°F) 1.98 Study , Study , Study , Study , Study , Study , Study , Study , Study 4. Study Is resistance within specifications or w/in Study? YES 1) Go to "CHECK PCM/TCM " as below NO 1) Study Guide Replace "TRANSAXLE FLUID TEMPERATURE SENSOR" as necessary and Go to "Verification Vehicle Repair"Study procedure. Study Guide , Study Guide , Study Guide , Study Guide , Study Guide Check TCM 1. Study Ignition "ON" & Engine "OFF". 2. Study Connect "TRANSAXLE FLUID TEMPERATURE SENSOR" connector. 3. Study Install scantool and slect a SIMU-SCAN, 4. Study Simulate voltage (0→5V) to "TRANSMISSION FLUID TEMPERATURE SENSOR" signal circuit. 5. Study Is FLUID TEMP. SENSOR signal value changed according to simulation voltage? YES 1) Study Thoroughly check connectors for looseness, poor connection, bending, corrosion, contamination, deterioration, or damage. Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure. NO 1) Study Substitute with a known-good PCM/TCM and check for proper operation. If the problem is corrected, replace PCM/TCM as necessary and go to "Verification of Vehicle Repair" procedure. Study Guide and Auto Repair and Study Guide and Auto Repair and Study   more Study Guide and Auto Repair

How to check output speed sensor code P0722

How to check output speed sensor code P0722

 

P0722 A/T Output speed Sensor Circuit - Open or Short(GND)

Study Guide

Auto Repair

Study Guide and Component Location Study Guide and General Description Study Guide and The Output Speed Sensor outputs pulse-signals according to the revolutions of the output shaft of the transmission. Study Guide and  The Output Speed Sensor is installed in front of the Transfer Drive Gear to determine the Transfer Drive Gear rpms by counting the frequency of the pulses.Study This value, together with the throttle position data, is mainly used to decide the optimum gear position. Study Guide and DTC Description Study The TCM sets this code if the calculated value of the pulse-signal is noticeably different from the value calculated, using the Vehicle Speed Sensor output, when Study the vehicle is running faster than 30 km/h. The TCM will initiate the fail safe function if this code is detected. Study Guide and DTC Detecting Condition Item to Study Detecting Condition and Study Study Possible Cause DTC Strategy ● Speed rationality check ● Signal circuit is open or short. ● Sensor power circuit is open ● Sensor ground circuit is open ● Faulty OUPUT SPEED SENSOR ● Faulty PCM Enable Conditions ● Battery Voltage ≥ 10V ● Lever position : D,3,2,L ● State of brake : OFF Threshold Value ● Output speed = 0 Diagnostic Time ● More than 1sec Fail Safe ● Locked into 3rd or 2nd gear. ● Manual shifting is possibe(2 nd → 3 rd ,3 rd → 2 nd) more cases and  information Study and Study and Study and Study and Study and Study and Study and Study

How input sensor works? code P0717

How input sensor works?code P0717

Model: Hyundai Elantra

Year Model: 2010

Fuel: Gasoline

Displacement: 1600cc

 

Transmission  Automatic Transaxle  P0717 A/T Input speed Sensor Circuit Low Input

Study Guide and Component Location Study Guide and General Description The Study Guide input(turbine) speed sensor outputs waveform signals according to the revolutions of the input shaft ,installed in front of End clutch retainer,of the transmission. The Study Guide TCM determines the input shaft speed by calculating the frequency of the pulses. This Study Guide value is mainly used to control the optimum fluid pressure during shifting. Study Guide and DTC Description The Study Guide PCM/TCM sets this code if an output pulse-signal is not detected, from the input speed sensor, when the vehicle is running faster than 30 km/h. The Study Guide Fail-Safe function will be set by the PCM/TCM if this code is detected. DTC Detecting Condition Item Study Guide Detecting Condition Study Guide Possible Cause Study Guide Study Guide and DTC Strategy ● Speed rationality check ● Signal circuit is open or short. ● Sensor power circuit is open ● Sensor ground circuit is open ● Faulty INPUT SPEED SENSOR ● Faulty PCM/TCM Study Guide Enable Conditions ● Battery Voltage ≥ 10V ● Output speed ≥ 1000rpm ● Engine speed(Only current gear is the 1st gear) ≥ 3000rpm ● Lever position : D,3,2,L Study Guide and Threshold Value ● Input speed = 0 Study Guide and Diagnostic Time ● More than 1sec Fail Safe ● Locked into 3rd or 2nd gear. ● Manual shifting is possibe(2 nd → 3 rd ,3 rd → 2 nd) Study Guide and Specification Input shaft & Output shaft speed sensor ● Type : Hall sensor ● Current consumption : 22mA(MAX) ● sensor body and sensor connector have been unified as one. Study Guide and Schematic Diagram Study Guide and Signal Waveform

more case and study guide